Radon in London Basements… Is the Ground to Blame?
If you manage a building with a basement in London, there is an invisible gas you are legally required to think about: Radon. Most people assume Radon is a problem for Cornwall or Derbyshire, not Central London. So, we looked into seven years of our own Radon monitoring for one of London’s largest private healthcare providers to find out what is really going on beneath the capital’s clinics, and whether the geology is the deciding factor.
What is Radon, and why do basements matter?
Radon is a natural radioactive gas with no colour, smell or taste. It forms when tiny amounts of Uranium break down in rocks and soils, and it is found everywhere in the UK. Outdoors it disperses harmlessly, but indoors it can build up.
It matters because radon is the second leading cause of lung cancer in the UK after smoking, linked to over 1,100 deaths each year (Public Health Wales). The average level in UK homes is around 20Bq/m3 (becquerels per cubic metre, the unit used to measure radon in air).
Basements are where radon tends to collect. They sit in direct contact with the ground and often have limited ventilation. That is why the law treats them differently:
- Every below-ground workplace needs a radon assessment, even in areas mapped as low risk (Public Health Wales).
- 300 Bq/m3 is the workplace action level. Above this annual average, the Ionising Radiations Regulations 2017 (ERR17) apply, and employers must act to reduce exposure.
- 100 Bq/m3 is the UK Target Level, the ideal outcome when reducing Radon in a building, and 200 Bq/m3 is the Action Level for homes.
The only way to know your level is to measure it. Radon cannot be predicted reliably for an individual building, even from a map.
What was looked at
Since 2019, Ground & Water has carried out Radon monitoring across the London estate of HCA Healthcare UK, including clinics and hospitals in Marylebone, St John’s Wood, Chelsea, London Bridge and the City. Because these are healthcare workplaces with staff and patients below ground, everyone was assessed regardless of the local radon map.
We brought together three rounds of monitoring:
- 2019: 42 buildings across seven HCA facilities, from the Harley Street Clinic to London Bridge and Lister hospitals.
- 2024: a return to five Harley Street and Great Portland Street basements, with detectors placed room by room.
- 2026: the lower ground space serving a new MR Linac radiotherapy bunker at Harley Street clinic.
In total, 77 detectors were placed in 43 basement buildings across six London boroughs, giving 51 valid results. Each detector was left in place for around three months, then analysed by a UKHSA-validated laboratory. A seasonal correction was applied to convert each reading into an annual average that can be compared with the 300Bq/m3 limit.
To test whether the ground made a difference, we then mapped the geology beneath every building using the British Geological Survey’s Geoindex, recording both the surface layers (Superficial deposits) and the solid rock below (bedrock).
What the data shows
- Every result was below the legal limit
Not one of the 51 results reached the 300 Bq/m3 workplace action level. The highest was 237 Bq/m3, around 79% of the limit and no building needed remedial work under IRR17.
- Most basements were low
42 of the 51 results (82%) were below 50Bq/m3, and the typical result was around 25 Bq/m3. That is close to the UK household average and in line with central London’s low radon potential.
- A handful stood out
Five results reached 100Bq/m3 or more: two at a Harley Street clinic in 2026 (105 and 237), and one each in Chelsea (140), at London Bridge (up to 127) and in St John’s Wood (up to 104). All are below the legal limit but above the UK Target Level, and they are spread across four different parts of London.
- Rooms in the same basement can differ hugely
At one Great Portland Street Basement, the corridor measured 67 Bq/m3 while the staff room measured 8, an eightfold difference a few metres apart. At London Bridge, two detectors in one building read 48 and 127.
- The same building can change over time
One Harley Street basement measured 25 Bq/m3 in 2019. When we returned in 2026 to monitor the new lower ground space serving its radiotherapy bunker, the results were 105 and 237 Bq/m3.
Why does it look like this? Is the ground to blame?
Geology sets the starting point
Radon begins in the ground, so geology decides how much is available to enter a building. Much of central London sits on the London Clay Formation, a dense, low-permeability clay that does not release much radon, and the UKHSA radon map puts our Marylebone sites in its lowest band (under 1%). That explains why most of our results were low.
We checked the ground under every building
Every building sits on the same bedrock: the clays of the London Clay Formation. What changes from site to site is the layer near the surface.
Higher results turned up on every type of ground
The five results of 100 Bq/m3 or more sit on three different types of ground from permeable river gravels to dense clay with nothing above it. Every type of ground with more than one result also produced low readings.
At London Bridge, one building read up to 127 Bq/m3 while its three neighbours on the same ground read 23 to 30. In Chelsea, a basement on river gravel read 140, while a site on the same gravel at Guy’s read 23. And the St John’s Wood result of 104 came from a building on clay, the ground least likely to let radon through.
Gravel may help radon move, but it doesn’t decide the result
Sand and gravel let gas move through them more easily than clay, and two of the five higher results sat on Kempton Park Gravel beside the Thames. But the typical result on that gravel was 27 Bq/m3, much like everywhere else, and four of its six results were 30 or below. With 37 of the 51 results on river terrace gravels ranging from 6 to 237 Bq/m3, the ground alone cannot explain which basements came out higher.
The building controls the detail
What varied between results was the building, not the ground. The condition of floor slabs and walls, gaps around pipes and cables, how well a room is ventilated, and whether it is closed store or a busy corridor all change how much radon gets in and how long it lingers. That is why two rooms in one basement can differ eightfold.
Building work can change the picture
New below-ground construction, refurbishment or changes to ventilation can open new pathways for radon or change how air moves. The rise seen at the Harley Street clinic between 2019 and 2026 is a reminder that a past result applies to the building as it was, not as it is now.
Deeper isn’t automatically worse
Five buildings had a lower (second) basement level. Four of them recorded 30 Bq/m3 or less, so depth alone did not predict higher radon.
In short: Geology gave London a low-radon starting point, and gravels may make it easier for radon to travel. But high and low results appeared on every type of ground, so the ground did not decide which basements came higher. The buildings did.
What this means for your building
If you run a workplace with a basement or lower ground floor, the message from our data is simple: a low-risk map does not replace a measurement. London’s geology keeps most results low, but the only way to know your buildings level is to test it.
- Test every below-ground workplace. It is a legal requirement, whatever the radon map says.
- Test more than one room. Results can vary several-fold within a single basement, so one detector can miss the highest room.
- Retest after building work. New basements, extensions, refurbishment or ventilation changes can all alter radon levels.
- Keep an eye on results above 100 Bq/m3. They are within the law, but above the UK Target level, and worth reviewing as a building changes.
Pro tip: Place detectors in the rooms people actually use, such as consulting rooms, offices and staff areas, as well as quieter spaces like stores and corridors, where radon can build up. A good monitoring plan reflects how the building is used, not just its floor plan.
Final thoughts
Seven years of monitoring across one of London’s busiest healthcare estates shows that radon in central London basements is usually low, and every building we tested was within the legal limit. The ground explains why London starts from a low base, but the building decides the final number. That is why measuring, rather than assuming, remains the only reliable answer.
At Ground & Water, radon monitoring sits alongside our ground investigation and Basement Impact Assessment work, so we understand both what is beneath your building and how the building itself performs. We plan where detectors go, install and collect them, have them analysed by a UKHSA-validated laboratory, and give you a clear report explaining what your results means and whether any action is needed.
Ground and Water Limited continues to work with HCA Healthcare to monitor as they observe best practice.
Author: Alex Bennett
